# What electrical work does a heat pump need?

> The circuits, disconnect, panel capacity and thermostat wiring a heat pump needs in a Bakersfield house, and how we check and coordinate each one.

URL: https://verandabakersfieldheatpumps.com/guide/heat-pump-electrical-requirements/

Learn

A heat pump runs on two 240-volt circuits, a disconnect and a thermostat that speaks its language; the panel decides how simple that is.

Last Updated: November 19, 2026

The short answer

A heat pump needs a 240-volt circuit for the outdoor unit with a disconnect near it, and usually a second 240-volt circuit for the air handler and its heat strips. The panel needs open spaces and enough service capacity for both, and the thermostat must handle heat pump controls. We check all of it at the site visit.

Key takeaways

- The outdoor unit and the air handler each get their own 240-volt circuit.
- A disconnect within sight of the outdoor unit lets the system be shut off safely for service.
- Open breaker spaces are only half the question; service capacity is the other half.
- Thermostat wiring often needs more conductors than an old AC system used.

## Will my panel handle a heat pump?

The answer comes from two numbers on your panel: how many open spaces it has and its service capacity. A panel can have empty slots and still be near its limit, for example after an EV charger, a pool pump or a kitchen remodel.

At [Veranda Bakersfield Heat Pumps](https://verandabakersfieldheatpumps.com/) we open the panel at the site visit, read the main breaker and the directory, and look at what is already drawing power. That check shapes the electrical lines on the [heat pump installation](https://verandabakersfieldheatpumps.com/heat-pump-installation/) estimate before you see a price.

### Choosing equipment around the panel

It also works the other way. Knowing what the panel can carry helps us choose the equipment. A variable-speed outdoor unit, a smaller heat strip bank or a different air handler can change the circuit sizes, and sometimes that choice keeps a panel upgrade off the estimate. Our [variable-speed guide](https://verandabakersfieldheatpumps.com/guide/variable-speed-heat-pumps/) explains how those systems draw power.

## Which circuits does a heat pump need?

A ducted heat pump has two pieces of equipment, and each gets its own supply.

| Equipment | Circuit | What sets its size |
| --- | --- | --- |
| Outdoor unit | Dedicated 240-volt | The unit’s nameplate rating for minimum circuit size and maximum breaker |
| Indoor air handler | Dedicated 240-volt | The blower plus the electric heat strips, if fitted |
| Disconnect at the outdoor unit | On the outdoor circuit | Within sight of the unit, rated for the circuit |
| Thermostat | Low-voltage control wiring | The equipment’s control board |

### The outdoor unit

If you are replacing a heat pump or an AC, there is already a 240-volt circuit and a disconnect in the side yard. We check that the wire size and breaker match the new unit’s nameplate, and that the disconnect is in good shape. Bakersfield sun and valley dust wear on these boxes, and a corroded disconnect gets replaced.

### The air handler

This is where conversions differ most. A gas furnace runs on a small 120-volt circuit; an air handler with heat strips needs a dedicated 240-volt circuit sized for those strips.

A typical Oildale conversion needed exactly that: a new 240-volt circuit for the air handler in the hall closet, run from a panel that had room. Our [conversion guide](https://verandabakersfieldheatpumps.com/guide/furnace-ac-to-heat-pump-conversion/) covers the rest of that job.

## What happens if the panel is short on room or capacity?

There are several ways to handle it, and the right one depends on the house:

- **Rearranging circuits.** Sometimes tandem breakers or consolidating lightly used circuits frees a space, where the panel allows it.
- **Choosing smaller heat strips.** In a mild Bakersfield winter, a smaller backup heat bank can be enough, which lowers the circuit size.
- **A subpanel.** Adds spaces where the service has capacity but the panel is full.
- **A panel or service upgrade.** Needed when the service itself is too small. This involves the utility and takes longer to schedule.

We tell you which applies at the visit, and the estimate shows the electrical scope on its own line, so you can see what it adds.

If you are replacing a heat pump that already has both circuits, the electrical side may be no more than a check and a new disconnect. Veranda’s typical range for a like-for-like ducted heat pump replacement is $6,500 to $15,500, set at the site visit.

## Why does the thermostat matter so much?

The thermostat is the brain of a heat pump. It tells the outdoor unit when to run, flips the reversing valve between heating and cooling, and decides when the backup strips come on. A plain AC and furnace thermostat cannot do all of that.

### Wiring

An old AC and furnace may have used four or five wires. A heat pump with backup heat typically needs more, including a common wire to power a modern thermostat. If the existing cable is short of conductors, we run a new one.

### Settings

The settings that matter most are the backup heat lockout and the balance point, which together decide how often the strips run. Set badly, the strips do the heat pump’s job and the bill shows it. Our guide on [auxiliary heat and thermostat controls](https://verandabakersfieldheatpumps.com/guide/auxiliary-heat-and-thermostat-controls/) explains what we set and why.

### Communicating systems

Some variable-speed systems use a communicating thermostat that talks to both units over a data connection. These need the matching thermostat from the same equipment line. Our [matching guide](https://verandabakersfieldheatpumps.com/guide/heat-pump-air-handler-and-outdoor-unit-matching/) covers how controls fit into the matched set.

## How does the electrical work get coordinated?

We schedule the electrical work with the rest of the installation so the circuits are ready when the equipment arrives. It sits inside the same project and permit, and the inspection covers it.

The permit office depends on the address, so we check it before filing, and the permit is a line in your written estimate. Our [permits guide](https://verandabakersfieldheatpumps.com/guide/bakersfield-heat-pump-permits/) explains the process.

> If the service needs an upgrade
>
> If the job needs a service upgrade, the utility has to be part of it. We tell you that at the visit, explain the steps and build them into the schedule.

## What do you need to do?

Very little. Before the visit, photograph the panel’s main breaker and directory, and the thermostat. On install day, clear the area in front of the panel and leave the panel cover on; the breakers and wiring behind it are for us.

- Tell us about plans for an EV charger or another large load; it changes the capacity picture.
- Check where your house stands with our [system readiness tool](https://verandabakersfieldheatpumps.com/tools/heat-pump-system-readiness/).

After startup we record the voltage and amp draw on both units and give you the readings. The [commissioning guide](https://verandabakersfieldheatpumps.com/guide/heat-pump-installation-commissioning/) shows what else we check. To get the panel looked at, [request an estimate](https://verandabakersfieldheatpumps.com/contact/) or call [(661) 269-7726](tel:+16612697726).

## Questions about this guide

### What if my panel has no open breaker spaces?

There are a few ways forward, from rearranging existing circuits to replacing the panel. We look at what is on the panel and its service size at the visit, explain the choices, and put the one that fits your house on the estimate before it is final.

### Does my old AC thermostat work with a heat pump?

Rarely. A heat pump thermostat has to control the reversing valve and the backup heat as well as the compressor and fan. We check the model and count the wires in the cable, then list a new thermostat or new wiring on the estimate if needed.

### Why does the air handler need its own circuit?

The electric heat strips inside it draw a lot of current when they run. A dedicated 240-volt circuit sized for those strips keeps them from tripping breakers or overloading a circuit that serves something else.

## More guides

- [Decision Guide**What changes when I switch from a furnace and AC to a heat pump?** The outdoor swap is the easy part; the work that sets the price happens in the closet, the panel and the attic.](https://verandabakersfieldheatpumps.com/guide/furnace-ac-to-heat-pump-conversion/)
- [Learn**Why does my thermostat say "aux heat"?** Auxiliary heat is the backup inside your air handler, and the thermostat settings decide how often it runs.](https://verandabakersfieldheatpumps.com/guide/auxiliary-heat-and-thermostat-controls/)
- [Learn**Do the indoor and outdoor parts of a heat pump have to match?** A heat pump is rated as a pair, not as two separate boxes, and the pair only delivers its numbers when it is put together right.](https://verandabakersfieldheatpumps.com/guide/heat-pump-air-handler-and-outdoor-unit-matching/)
- [Learn**What happens during heat pump startup and commissioning?** The last hours of an install decide whether a new heat pump runs the way it was designed to, and we check each step in order.](https://verandabakersfieldheatpumps.com/guide/heat-pump-installation-commissioning/)
- [Learn**Do I need a permit for a heat pump in Bakersfield?** The office that issues your permit depends on where your parcel sits, so we check your address before anything is filed.](https://verandabakersfieldheatpumps.com/guide/bakersfield-heat-pump-permits/)

## Get an estimate for your house

(661) 269-7726
